Extremely compact case that still takes full-size parts. The build process is a bit of a challenge, and if you're going to push that 270mm GPU limit (mine's 260mm), you're going to have to be prepared to dismantle more of the case than you'd planned on to make it fit. On paper, this case accepts an ATX PSU, to which I say, "Sure, if you're not using a graphics card." All that said, for as challenging a build as this case can be, it is exceptional. Tons of room for full-size components inside a chassis that's really not all that much bigger than a Silverstone SG-13. It's about 50% taller, but not quite as wide or deep. The build quality is great, and the leather handle feels nice and sturdy when transporting the system. Every panel except behind the motherboard is a metal mesh, so plenty of ventilation. I could keep going, because I really do love this case. It's a perfect blend of size and compatibility for me, an ITX enthusiast who likes a portable system but doesn't want to be stuck with half-height GT 1030s. Definitely, 100% recommended. Read more

I wanted a portable system for gaming and light production work. The G200 is one of the few ITX cases that remains small and easily portable, while accepting a regular horizontal GPU mount and full size CPU cooler. Cabling is finicky, as small form factor always is. The hardest part was getting to the CPU fan headers with the cooler installed. This would have been easier if I had gotten a single tower cooler, or if the motherboard header pins were in a different spot. By ITX case standards, the build was overall very easy. I'll list the parts I installed below as an example of components that work in the case. Though it supports an ATX PSU, I highly recommend using SFX as you will likely need the extra room for cables. Feels solid enough, yet light enough to carry around easily. Handle seems well up to the task. I'm very happy with the G200. Motherboard: ASRock B650i Lightning Wifi CPU: Ryzen 7700x Cooler: Thermalright Peerless Assasin Rear Exhaust Fan: Thermalright TL-C12CW Memory: 2x32gb G-Skill Flare x5 PSU: Cooler Master V850 SFX Drive: Teamgroup MP34 4 TB nvme GPU: PNY Verto 3060 Ti (a Zotac Twin Edge 4070 also fits nicely) Read more

Bought this for my son as he wanted me to build him a pc for traveling, so small form factor was it. Used a Aorus B550i pro ax board with a 5900x cpu, 6700xt graphics card with a Seasonic 750w psu a few months ago and it allows the hot equipment to breathe, great air flow case, solid metal case so build quality is awesome, a little on the heavy side but still light enough to travel comfortably with. My son is very happy with the case so i am a very happy dad as it did work out rather well for us, so very happy and satisfied with purchase. Read more

Upgrading from an mATX to an ITX motherboard required a new case - I still needed a case that can fit an ITX motherboard, but be slightly big enough to hold a single 3.5 HDD. And this case fit the picture (but with a few things to point out). To start, the case description does say it'll allow a 269mm (iirc) GPU. BUT ONLY if you use SFX-L or SFX PSU. I was lucky I had an SFX-L on hand that that was no issue, but if you plan to use an ATX PSU, be warned that your card may not fit if it is that long. Secondly - to fit a GPU of that length, you do need to disassemble the bottom part of the case. The case is DIY friendly and it is all put together by screws, so you can put thing together as such. Third - if you plan to use a 3.5 HDD, you must use SFX/SFX-L PSU. In my case, this worked to my advantage and I was able to fit the HDD on the other side of the panel. A minor detail is that if you plan to use an intake fan for the case on the top part, you may want to use a low-profile 120mm and install that FIRST prior to your motherboard for fitment testing. For me, I did not do that cause I already installed the motherboard, heatsink, and GPU already - oops! Otherwise, my specs are: i7 13700f 64GB DDR5 4800MHz ASUS RTX 4070 Dual (this card just fits!) 2x 1TB NVME 4TB HDD Corsair SFX-L 850w Gold. Temperatures are all great due to the almost-full mesh design of the case - under stress loads, CPU generally hovered around 83-85C with a few spikes up to 90C. GPU was at a cool 73C, with hotspot at 82C. Your NVME drive may suffer a bit, depending on its own cooling solution and your setup arrangement - mine idles at 53C but under loads goes up to 67C. Cable mangement in this case is fair - you can route your cables behind the motherboard panel, but it depends on your length cables. Since I have an SFX-L PSU, it was a bit more trickier to keep it cleaner so using a SFX PSU may netyou overall better cable management IMO. The case handle on top feels firm and allows you to easily move your case around, or take it with you if you plan to go somewhere. The magnetic dust filter it comes with is... eh, it works - it feels a bit cheap but it'll do its job preventing dust buildup under your case. Overall, I am pleased with this case and form factor - it will allow more desk space while also retain some flexibilty like installation of SFX/SFX-L/ATX PSUs, slightly longer GPU (depending on PSU selection), and a 3.5 HDD (again, depending on PSU selection). Read more

Este gabinete es es de 12.8 litros por lo que es muy compacto y apto para el transporte ya que incluye un mango de muy buena calidad y muy robusto ademas de que cabe en una maleta de mano (perfecto para llevarlo en cabina de avión) y con una ventilación espectacular que permite equiparla con componentes de gama media-alta sin comprometer las temperaturas. Lo equipe con lo mas potente que pude pero sin comprometer las temperaturas, lleva un ryzen 9700x de 65W, un disipador be quiet rock slim 2 de 92mm, una fuente corsair sf1000 y una asus dual rxt 4070 super y ademas permite un disco duro de 3.5 o 2.5 (yo agregue uno de 2.5 con un adaptador sabrent de 3.5 a 2.5 que compre también en amazon ya que el disco se debe atornillar por debajo y no por los costados), y para la ventilación use dos ventiladores noctua en las partes trasera y superior de 120 mm (el superior debe ser de 15 mm de ancho) ambos en modo extracción. Con esto tengo un equipo que es perfecto para gaming a 1400p, que no pasa de los 7kg de paso, compacto como una caja de zapatos y con un gran control de temperaturas gracias a la presión negativa generada por los ventiladores y junto a su diseño completamente de malla resulta en un gran flujo de aire que permite que ni el procesador ni la grafica pasen de 80 grados cuando están al 100% de uso. Por mi parte estoy mas que contento con mi setup portátil que me permitirá aprovecharlo al máximo tanto para gaming como para productividad que ademas puedo llevar en mis viajes, por lo que si quieres algo de esta categoría y esta portabilidad no hay nada igual en el mercado. Read more

This case does exactly what it is supposed to do. The materials feel high quality and it came well packed with nice soft foam protecting it inside the box. The steel might feel just a little thin on the side panels, but not any kind of problem and that helps keep this a bit lighter since it is supposed to be prtable tih the handle on top. The front panel cables for USB connections were actually much better quality than many much more expensive cases I have used. Very high quality and flexible and easy to use. Everything is finished nicely and there are no sharp edges or anything like that. The handle feels nice and sturdy, and I love that I can fit a full-size air cooler in this case. I have this setup with a 13600K, Deepcool AK620 air cooler, an ASUS Dual RTX 4070 GPU, and a Corsair SF600 PSU. It's the perfect portable rig !! Air flow is just fine. Setting it up with 2 exhaust fans (one slim 120mm on top and a 92mm in the rear and its plenty to keep air moving inside the case and everything running cool. The GPU has plenty of access to fresh air thru the well-ventilated case bottom. It was extremely easy to work in, with the one piece of advice I have for building in this case being.... Make sure that you hook up all wires and cables at the top of the motherboard BEFORE you install the CPU cooler. If you are using a large air cooler, once it's installed getting to those connections on top is basically impossible. Also, there isn't a ton of room behind the motherboard for cable mess, but this case doesn't have a side window anyway so stuffing excess cables neatly below the PSU was not a problem. You can't see any of it once the case is closed. Read more